Kohesi: Jurnal Sains dan Teknologi

Articles

Vol. 10 No. 8 (2026): Kohesi: Jurnal Sains dan Teknologi, ISSN 3025-1311

ANALISIS PROSES PRODUKSI STAY CLAMP B6H DENGAN BAHAN BAJA YSH270C

Submitted
January 26, 2026
Published
2026-01-26

Abstract

Penelitian ini bertujuan untuk menganalisis proses produksi komponen Stay Clamp B6H berbahan baja YSH270C berdasarkan waktu produksi efektif dan efisiensi produksi pada setiap tahapan proses. Proses produksi yang dianalisis meliputi blank piercing, bending, dan restrike yang dilakukan menggunakan mesin press mekanik. Metode penelitian yang digunakan adalah pendekatan kuantitatif deskriptif dengan pengambilan data waktu proses aktual pada setiap tahapan produksi. Waktu produksi efektif dihitung dari penjumlahan waktu pemotongan dan waktu tambahan, sedangkan efisiensi produksi ditentukan berdasarkan perbandingan antara output aktual dan output teoritis. Hasil penelitian menunjukkan bahwa waktu produksi efektif pada proses blank piercing sebesar 3,5 detik, sedangkan pada proses bending dan restrike masing-masing sebesar 4,2 detik. Efisiensi produksi tertinggi diperoleh pada proses blank piercing sebesar 85,1%, sementara proses bending dan restrike masing-masing memiliki efisiensi sebesar 73%. Perbedaan efisiensi ini dipengaruhi oleh besarnya waktu tambahan pada setiap proses. Hasil penelitian ini diharapkan dapat menjadi dasar evaluasi untuk meningkatkan efisiensi proses produksi Stay Clamp B6H.

This study aims to analyze the production process of the Stay Clamp B6H component made of YSH270C steel based on effective production time and production efficiency at each processing stage. The analyzed manufacturing processes include blank piercing, bending, and restrike, which are performed using a mechanical press machine. The research method employs a descriptive quantitative approach by collecting actual process time data at each production stage. The effective production time is calculated from the sum of cutting time and additional time, while production efficiency is determined by comparing actual output with theoretical output. The results show that the effective production time for the blank piercing process is 3.5 seconds, while the bending and restrike processes each require 4.2 seconds. The highest production efficiency is achieved in the blank piercing process at 85.1%, whereas the bending and restrike processes each have an efficiency of 73%. The differences in efficiency are mainly influenced by the amount of additional time required at each process. These findings are expected to serve as a basis for evaluating and improving the efficiency of the Stay Clamp B6H production process.

References

  1. [1] J. Mucha and J. Tutak, “Analysis of the Influence of Blanking Clearance on the Wear of the Punch, the Change of the Burr Size and the Geometry of the Hook Blanked in the Hardened Steel Sheet,” Materials, vol. 12, no. 8, p. 1261, Apr. 2019, doi: 10.3390/ma12081261.
  2. [2] A. L. O. Zaid, “Blanking and piercing theory, applications and recent experimental results,” IOP Conf. Ser.: Mater. Sci. Eng., vol. 60, p. 012065, Jun. 2014, doi: 10.1088/1757-899X/60/1/012065.
  3. [3] Qomaruddin, A. Z. Hudaya, S. Khoeron, and Moh. S. Syamsuddin, “Pembuatan Press Dies Proses Blanking dan Piercing pada Handle Tanam Pintu Geser,” IMEJOUR, vol. 2, no. 2, pp. 69–83, Nov. 2024, doi: 10.56904/imejour.v2i2.45.
  4. [4] N. Arifin, D. T. Santoso, and A. Santosa, “Proses Produksi Gasket pada Mesin Press Aida DSF-C1800A di PT. XYZ,” JMN, vol. 7, no. 1, pp. 24–33, Jun. 2024, doi: 10.29407/jmn.v7i1.20309.
  5. [5] M. Nevenda and L. M. C. Wulandari, “ANALISIS PERHITUNGAN WAKTU STANDART UNTUK MENENTUKAN JUMLAH TENAGA KERJA OPTIMAL PADA PROSES PRODUKSI PT. NRZ PRIMA GASKET,” vol. 1, 2023.
  6. [6] A. L. O. Zaid, “Blanking and piercing theory, applications and recent experimental results,” IOP Conf. Ser.: Mater. Sci. Eng., vol. 60, p. 012065, Jun. 2014, doi: 10.1088/1757-899X/60/1/012065.

Similar Articles

31-40 of 338

You may also start an advanced similarity search for this article.